Green Element

Fiberglass LED Pool Light 35W

Size: 250*60mm  8mm
Material: SS316
LED: 441pcs SMD leds
Power: 35w
Color: single color / RGB and RGBW
Voltage: AC12v
Waterproof class: IP68

Simple introduction:

1. Selected glass, equipped with ultra-high brightness LED as the light source of small power.
2. Voltage: AC 12V.
3. Projection angle rang: 25degrees to 120 degrees optional, the body working operation temperature < 65 degrees.
4. Colours: Red, green, blue, yellow, white, seven colors gradual changing, jumping changing, and others, power switch mode & remote controller pattern for your choice.
5. Spanlife more than 30, 000 hours, low power consumption, environmental protection friendly.
6. IP68.
7. Application: Widely applied into many fields like: Garden fountains, squares surface, water column surface, and outdoor, swimming pool, pond, lake, etc.

FLAT LIGHT GREEN 25CM

8mm LED Pool Light 20W


Product Description:

Ultrathin LED Fountain lights, Ultrathin LED Pool Lights, led pool lights, led pond lights, led spa lights,led slim pool light,slim led pool light

Dimension: D200mm*H8mm 

Specification:

Material:PC

Light color: green,blue,red,yellow,white,RGB

Voltage: DC12V

Watt: 20W 1800LM

Color Temperature:2700k-6500k

LED Chip: SamSung Brand

Waterproof grade: IP68

Beam angle: 120°

Working environment temperature: -25°C~45°C

Control method: Inbuilt driver

Working Lifetime 50,000 hrs

Advantage:

1) Install easily ONLY with 2 screws

2)  Ultra-flat only 8mm slim.

3) Replacing and install by 3 minute(much down the maintain cost)

4) Never don't worry water leaking

5) High brightness LED

6) Available DMX signal

FLAT LIGHT GREEN 20CM 

Ultrathin LED Fountain lights, Ultrathin LED Pool Lights, led pool lights, led pond lights, led spa lights,led slim pool light,slim led pool light

Dimension: D160mm*8mm

Specification:

Material: SS316

Light color: green,blue,red,yellow,white,RGB

Voltage: DC12V

Watt: 10W 800LM

Color Temperature:2700k-6500k

LED Chip: SamSung Brand

Waterproof grade: IP68

Beam angle: 120°

Working environment temperature: -25°C~45°C

Control method: Inbuilt driver

Working Lifetime 50,000 hrs

Advantage:

1) Install easily ONLY with 2 screws

2)  Ultra-flat only 8mm slim.

3) Replacing and install by 3 minute(much down the maintain cost)

4) Never don't worry water leaking

5) High brightness LED

6) Available DMX signal

FLAT LIGHT GREEN 16CM 

Ultrathin LED Fountain lights, Ultrathin LED Pool Lights, led pool lights, led pond lights, led spa lights,led slim pool light,slim led pool light

Dimension: D100mm*H8mm

Specification:

Material:PC

Light color: green,blue,red,yellow,white,RGB

Voltage: DC12V

Watt: 10W 800LM

Color Temperature:2700k-6500k

LED Chip: SamSung Brand

Waterproof grade: IP68

Beam angle: 120°

Working environment temperature: -25°C~45°C

Control method: Inbuilt driver

Working Lifetime 50,000 hrs

Advantage:

1) Install easily ONLY with 2 screws

2)  Ultra-flat only 8mm slim.

3) Replacing and install by 3 minute(much down the maintain cost)

4) Never don't worry water leaking

5) High brightness LED

6) Available DMX signal

FLAT LIGHT GREEN 10CM

ROBUST STEEL ARMS OF POOLS
Ladder handrails are made of φ42mm tubes in polished stainless steel 304 (or 316 for saltwater pools). Correct selection and proper placement of handrails and ladders add a significant measure of safety to every pool area. Three kinds of step are available: Plastic, stainless steel, and stainless steel with anti-slip pads. All ladders are available with anchor or flange type fixtures for easy installation.

Product Features
Handrails is made from polished Stainless Steel 304 or 316(Ф42mm) tube
Steps available in stainless steel and plastic
Complete with anchoring fixtures or flange fixtures

STRAIGHT CONNECTOR FOR HANDRAIL

POOLSUPPLIES

Reduce the strain and effort of rolling up your solar cover with the Sun2Solar® Easy Gear Stainless Steel Cover Reel. This durable and dependable solar reel is designed with a unique gear system that reduces your required effort by 50%. Use the extra time and energy saved relaxing in your pool instead of struggling with a solar blanket.

Note: Reel is not recommended for use with our 1600 series solar cover. Will work with 800 and 1200 series solar covers

Features:

Frame constructed from durable stainless steel
Cover reel tubes measure 3¼" in diameter
Sturdy handle easily allowing for one person operation
Large treaded tires provide for easy maneuvering and makes rolling it out of the way a simple task
Includes all attachment hardware
Measurements:

Reel measures 18" high to the center of the pole
Base measures 22" wide from the outside of the wheels

ROLLER FOR POOL COVER 

SUPPORT FOR HANDRAIL

STRAIGHT HANDRAIL

ROBUST STEEL ARMS OF POOLS
Ladder handrails are made of φ42mm tubes in polished stainless steel 304 (or 316 for saltwater pools). Correct selection and proper placement of handrails and ladders add a significant measure of safety to every pool area. Three kinds of step are available: Plastic, stainless steel, and stainless steel with anti-slip pads. All ladders are available with anchor or flange type fixtures for easy installation.

Product Features
Handrails is made from polished Stainless Steel 304 or 316(Ф42mm) tube
Steps available in stainless steel and plastic
Complete with anchoring fixtures or flange fixtures

GRABRAIL HANDRAIL

EXIT HANDRAIL ARV

EXIT HANDRAIL ARP

EXIT HANDRAIL ARN

EXIT HANDRAIL ARG

EXIT HANDRAIL ARB

EXIT HANDRAIL ARA

END CAP FOR HANDRAIL

CURVED CONNECTOR FOR HANDRAL

LADDER LOWER PART 3 STEPS

STANDARD LADDER EMAUX

ROBUST STEEL ARMS OF POOLS
Ladder handrails are made of φ42mm tubes in polished stainless steel 316 for saltwater pools. Correct selection and proper placement of handrails and ladders add a significant measure of safety to every pool area. Three kinds of step are available: Plastic, stainless steel, and stainless steel with anti-slip pads. All ladders are available with anchor or flange type fixtures for easy installation.

Product Features
Handrails is made from polished Stainless Steel 316(Ф42mm) tube
Steps available in stainless steel and plastic
Complete with anchoring fixtures or flange fixtures

OVER FLOW LADDER EMAUX 316

ROBUST STEEL ARMS OF POOLS
Ladder handrails are made of φ42mm tubes in polished stainless steel 304 . Correct selection and proper placement of handrails and ladders add a significant measure of safety to every pool area. Three kinds of step are available: Plastic, stainless steel, and stainless steel with anti-slip pads. All ladders are available with anchor or flange type fixtures for easy installation.

Product Features
Handrails is made from polished Stainless Steel 304 (Ф42mm) tube
Steps available in stainless steel and plastic
Complete with anchoring fixtures or flange fixtures

OVER FLOW LADDER EMAUX

MURO LADDER EMAUX

INCLIEND LADDER EMAUX

Aqua

Manual mixer produced by the Italian company AQUA, designed for mixing various chemical reagents (acid and alkali solutions) in tanks. They are intended for installation on a working container for the purpose of preparing and maintaining chemical reagents in a condition suitable for pumping by pumps. Containers are attached from above. The mixer is made of PVC. The Aqua A-TANK-1 capacity of 100 liters is suitable for this mixer.

MANUAL MIXER PVC SHAFT 60CM

Astralux

MONOPHASE OR TRIPHASE MIXERS

The mixer is used with size tank from 100 l to 1000 l.
The gear box (lubrification free) is coupled to the tank fixing flange.
The main axis is made in stainless steel and covered in PVC.
The seal against chemical vapour is a Fluorocarbon rotary seal inserted between the flange and the PVC cover of the shaft. This protects the gear box and the motor from chemical vapour.

MOTORIZED MIXER

Seko

SEKO’s solenoid dosing pumps are the smart choice for water treatment processes where precise, consistent chemical dosing is essential. From potable water treatment systems to chemical dosing for agricultural applications, you’ll always find a perfectly-matched solution within our comprehensive solenoid-driven dosing pumps range.

Powerful microprocessor technology guarantees dosing accuracy, while wall and base-mounting options, constant and proportional dosing and analogue and digital variants provide unrivalled choice. Most of these solenoid diaphragm pumps can even be used without performance loss in locations with no access to mains electricity or where power supply fluctuates courtesy of SEKO’s stabilised multi power supply.

The use of premium materials such as PVDF and food-grade PTFE in the liquid end components gives our solenoid dosing pumps the flexibility to be used in multiple applications, as they have high resistance to a variety of aggressive chemicals including highly-corrosive substances such as acids.

With just a single moving part, these diaphragm pumps are virtually wear-free and require no lubrication of bearings or shafts, minimising maintenance requirement and repair costs whilst offering excellent continuous-running characteristics.

DOSING PUMP SEKO

Infinity

6 LPH @ 4 bar Pressure
Infinity positive displacement diaphragm metering pump operating at 230V, 50Hz supply.
It is base mountable. Solenoid push the diaphragm which in turn pushes the liquid into the system.
Solenoid is actuated by a solid state electronic circuit. It has controls for the desire accuracy of the dosing. Dosing rate @ 4 kg/cm²: 6.0 LPH (IDP 6)
Suction/Discharge tubing: 4/6 mm
Frequency: Up to 400 SPM
Electrical: 230V AC, 50 Hz
Power Consumption: 30 Watts
Fuse: 500mA / 230V AC
Pump Stroke per minute: 120 Max ( Adjustable)
Negative Suction: 1 Mtr
Environment Temperature: 40°C Max
Head: HDPE
Diaphragm: Teflon (PTFE)

DOSING PUMP INFINITY 5L/8BAR DIGITAL WITH FLOAT

DOSING PUMP INFINITY 5L/8BAR

PISTON

The Etatron AP range of piston dosing pumps are designed for applications requiring larger precise flow rates up to 190L/hr and higher pressures up to 20 bar. This range is not suitable for use with liquids containing abrasive or solid particles. This metering pump series can be controlled in various ways depending on application requirements, including; 4-20 mA signal and inverter control.



The metering pump head is available in either PVC, PVDF or stainless steel AISI 316 depending on the nature of the fluid. Seal materials options include; NBR, FPM and EPDM. This combination of materials options make this pump range suitable for a wide range of fluids and applications.



This dosing piston pump series is ideal for many applications in the industrial and marine markets, including; chemical dosing for maintaining PH levels in water treatment processes, Legionella dosing, biocides,  OEM dosing systems, reverse osmosis, chemical injection and chemical dosing for agriculture.

PISTON DOSING PUMP 

The Etatron AP range of piston dosing pumps are designed for applications requiring larger precise flow rates up to 190L/hr and higher pressures up to 20 bar. This range is not suitable for use with liquids containing abrasive or solid particles. This metering pump series can be controlled in various ways depending on application requirements, including; 4-20 mA signal and inverter control.



The metering pump head is available in either PVC, PVDF or stainless steel AISI 316 depending on the nature of the fluid. Seal materials options include; NBR, FPM and EPDM. This combination of materials options make this pump range suitable for a wide range of fluids and applications.



This dosing piston pump series is ideal for many applications in the industrial and marine markets, including; chemical dosing for maintaining PH levels in water treatment processes, Legionella dosing, biocides,  OEM dosing systems, reverse osmosis, chemical injection and chemical dosing for agriculture.





Product Summary 



•                      Etatron AP series piston metering pump

•                      Larger precise flow rates up to 190 L/hr

•                      Discharge pressures up to 20 bar

•                      10% to 100% stroke length adjustment

•                      Pump head available in  PVC, PVDF  or stainless steel AISI 316

•                      Seals available in NBR, FPM or EPDM

•                      Fitted with either single or double ceramic ball valves

•                      4-20 mA control possible with optional servo motor mechanism

•                      Level control supported

•                      Can handle fluids with viscosities up to 2000cp

•                      Self-priming

•                      120 strokes per minute maximum

•                      Aluminium casing with epoxy/acid proof coating

•                      IP55 motor protection

•                      Single phase 230V, 110V or three phase 230/400V 50/60Hz motors available

•                      Available with Atex motor for installation in non-safe areas

•                      Available with motors suitable for operation via external inverter (variable frequency drive VFD)

DOSING PUMP AQUA PH W/O PROB

AQUA HC997 is multifunction solenoid driven dosing pump with constant and proportional dosing with push buttons interface and digital LCD display for programming.


General Specifications:

LCD Display with Backlight
5 pushbutton interface
Constant Mode: flow rate, time, quantity, cyclic
Proportional Mode: 4-20mA input, pulse input, PPM
Time Mode: Daily or Weekly
Alarm: Level & Flow
Relay output
Maximum Flow 14 l/hr @ 0 bar
Maximum Pressure 20 bar @ 2 l/hr
Tube Connection Size 4mm x 6mm
Power Supply 230VAC
ON / OFF Switch
Level Input (pump interlock)
Wall & Bench Mounting Kit
IP65 Rating
Wetted Parts:

Pump Head PVDF
Ball Valves PTFE
Valve Body PVDF
Fittings PVDF
Injection Valve PVDF, Hastelloy, PTFE
Foot Valve PVDF
Seals Viton or EPDM

DOSING PUMP AQUA 5L/8BARS DIGITAL WITH AUX O/P

High Flow Plastic pumps.
Centrifugal electric pumps for swimming pools, with built-in pre-filter, ideals for high flow at low pressure.
Pre-filter with transparent lid in polycarbonate which allows easy observation of the pre-filter basket. The pre-filter is closed with a knob system of easy accessibility.
Pump body and pre-filter made in polypropylene reinforced with fibreglass, resistant to the chemical products in the swimming pool, guaranteed to last a long time.
Bronze, plastic or stainless steel impeller, according to model.
Motor shaft manufactured in stainless steel AISI 316L.
Pre-filter basket in stainless steel too.
Motors with IP-55 protection, at 2.850 r.p.m. Tension of mains feed at 230/400V-50Hz or 400/690V-50Hz (7,5, 10 and 12,5 HP) three-phase.
Versions from 4HP to 12,5HP.
Possibility of AISI 316L stainless steel impellers upon request.

SWIMMING POOL PUMP IML ATLAS SERIES

Self-priming centrifugal electric pump for swimming pools. Self-priming at 2 m.
Built-in pre-filter of great capacity (8 litres).
Pre-filter with transparent lid in polycarbonate which allows easy observation of the pre-filter basket. The pre-filter is closed with a knob system of easy accessibility.
Pump body made in polypropylene reinforced with fibreglass, resistant to the chemical products in the swimming pool, guaranteed to last a long time.
Mechanical seal in graphite and ceramics.
Motor shaft manufactured in stainless steel AISI 316L.
Motor with IP-55 protection, at 2.850 r.p.m. Tension of mains feed at 230/400V-50Hz three-phase (Ask for 400/690V-50Hz versions).
Possibility of IE2 Efficiency Motors upon request
Possibility of 60Hz upon request.
Versions of 3HP, 4HP and 5,5HP.
Suction connection Ø90 mm, return connection Ø75 mm. Both supplied with bush connections.

SWIMMING POOL PUMP IML 4HP DY SERIES

Self-priming electric pump for swimming pools, with built-in pre-filter of great capacity
Pre-filter with transparent lid in polycarbonate which allows easy observation of the pre-filter basquet. The pre-filter is closed with a knob system of easy accessibility
Pump body made in polypropylene reinforced with fibreglass, resistant to the chemical products in the swimming pool, guaranteed to last a long time.
Mechanical seal in graphite and ceramics
Motor shaft manufactured in stainless steel AISI316L
Enclosed motor, totally silent, with IP-55 protection, at 2.850 r.p.m
Tension of mains feed at 230V-50Hz sigle phase or 230/400V-50Hz three-phase
Possibility of 60Hz upon request
SE2N

2” inner thread connections
Installation dimensions exactly the same as the old Series Europa

SWIMMING POOL PUMP IML SE SERIES

Self-priming electric pump for swimming pools, with built-in pre-filter.
Pre-filter with transparent lid in polycarbonate which allows easy observation of the pre-filter basket. The pre-filter is closed by means of a thread, ensuring the perfect adjustment of the lid.
Pump body made in polypropylene reinforced with fibreglass, resistant to the chemical products in the swimming pool, guaranteed to last a long time.
Pump body lid and diffuser in Noryl. Impeller in Noryl with shaft in stainless steel.
Mechanical seal in graphite and ceramics.
Motor shaft manufactured in stainless steel AISI 316L.
Enclosed motor, totally silent, with IP-55 protection, at 2.850 r.p.m. Tension of mains feed at 230V-50Hz single-phase or 230/400V-50Hz three-phase.
Possibility of 60Hz upon request.
Connections of suction and return at 2 ¼” for Ø 50 mm bush connections.
Bush connections included with the pump.

SWIMMING POOL PUMP IML SA SERIES

Emaux

SUPREME PERFORMANCE SELF-PRIMING PUMP
Ultra-Power is a series of high-performance pumps designed to achieve the highest flows among similar pumps on the market. By utilizing state-of-the-art engineering, the one-piece molded pump body with a large capacity 8-liter strainer basket makes it unique among all comparable pumps. Built with corrosion and chemical resistant glass-reinforced thermoplastic and superior seawater graded mechanical seal guarantee a long working life.

SWIMMING POOL PUMP EMAUX ULTRA POWER

THE BEST OPTION FOR SMALLER PLUMBING
The SS pump is quiet running and energy efficient. 1.5-inch suction and discharge port with a transparent lid. It operates at a low decibel and energy consumption which requires minimal maintenance.

Product Features
1.5 inch suction and discharge ports
Asynchronous, two-pole motor
Class insulation: 130(B)
IPX5 Waterproof standard
Built-in thermal protection
Overload protection
External heat sink
Available in 50Hz or 60Hz with 220V/110V
Specially designed unions compatible for both Imperial and Metric standards
316 stainless steel shaft
316 stainless steel mechanical seal
Low noise level, low energy and easy maintenance

SWIMMING POOL PUMP EMAUX SS SERIES

ROBUST PUMPS FOR ABOVE-GROUND POOLS
The Emaux All-Star series pump is specifically designed as a superior pump for above-ground pools. Heavy duty construction and advanced engineering deliver high flow performance and reliability. It offers a powerful, quiet, and a long operational lifespan.
Includes a motor shroud for Canada versions and a mounting base. All components are molded in corrosion-proof reinforced thermoplastic for superior strength and reliability.
Easy access discharge port allows conversion from vertical to horizontal discharge orientation.
1.5” PVC pipe union or NPT thread to 1.25” – 1.5” hose band adaptor for quick inlet/outlet hose connection.
Large debris basket with see-through lid reduces cleaning frequency. Twist-Lock lid design enables hassle-free access to the basket.
Optimal volute and impeller design provides an excellent hydraulic performance.
Suitable for in-ground pools: self-priming vertical lift up to 5ft (1.5 metres).
Super quiet operation especially for dual-speed models.
Heavy duty high performance motor with automatic thermal overload protection.

SWIMMING POOL PUMP EMAUX ASC 150 M

A HIGH-PERFORMING SELF-PRIMING PUMP
Ring lock seal design eliminates suction leaks and maximize suction efficiency.

Product Features
Asynchronous, Two poles motor
Class insulation: 130(B)
IPX5 Waterproof standard
Built-in thermal protection
Overload protection
Available in 50Hz or 60Hz with 220V/380V
Special design union compatible for both imperial and metric standard
Imperial and Metric measurement standard
316 Stainless steel shaft
316 Stainless steel mechanical seal
Self-Priming up to 2.5m above water level
Testing pressure 50 PSI (3.5 Bar)
Basket Volume 5 litres

SWIMMING POOL PUMP EMAUX SC SERIES

SWIMMING POOL PUMP EMAUX 3HP VARIABLE SPEED

PROVEN LONG-TERM DURABILITY
The SB Series pump delivers high flow and energy efficiency ultra performance. 2-inch suction and discharge port with a transparent lid. Ring lock seal design to eliminate suction leaks and to maximize suction efficiency.

Product Features
2 inch suction and discharge ports
Ring-lock lid eliminates leaks andmaximizes suction efficiency
Asynchronous, two-pole motor
 Class insulation: 130(B)
IPX5 Waterproof standard
Built-in thermal protection
Overload protection
Available in 50Hz or 60Hz for 220V/380V
Specially designed unions compatible for both Imperial and Metric standards
Testing Pressure (50PSI / 3.5Bar)
316 stainless steel shaft
316 stainless steel mechanical seal

SWIMMING POOL PUMP EMAUX SB SERIES

Commercial Iron Pump
FOR HEAVY DUTY APPLICATIONS
Product Features : 
1. Cast iron body with AISI-304 stainless basket
2. Optional AISI-304 stainless steel or cast iron
 impellers depending on requirement.
3. Asynchronous, two-pole motor
4. Class insulation: 130(B)
5. IPX5 Waterproof standard
6. Built-in thermal protection
7. Overload protection
8. Available in 380V/50Hz
9. Testing Pressure 50PSI (3.5 Bar)
10. Basket Volume 5 litres

SWIMMING POOL PUMP EMAUX COMERCIAL SE SERIES

Supplied with unions of dia. 63 mm, thread of 2"3/4;
 

Ultra-Silent pump;
 

Resined motor for total protection and stability;
 

Axe made in Stainless Steel AISI316L;
 

Anti-Vibration NSK bearings;
 

All Gaskets and O-Rings in Viton;
 

Mechanical seal in Silicon Carbide;
 

Impeller in reinforced Noryl;
 

Designed to work in high temperatures;
 

Body in resistant reinforced materials;

 

Insulation Class F;
 

Resistant to salt treatment and sea water;
 

All motors with thermal cut-out protection.

SWIMMING POOL PUMP BLUESPACE ORION 2 INCHES

LYRA
Extremely silent pump with resin-coated motor for maximum protection of electrical components. AISI 316L stainless steel shaft working on high quality anti-vibration bearings. Viton gaskets that guarantee excellent resistance to chemical agents. The Silicon Carbide mechanical seal and the glass fiber reinforced Noryl impeller make this pump extremely robust and reliable. It is designed to operate at high temperatures. All single-phase motors are equipped with thermal protection. All pumps have a transparent cover with folding knob closure, double water drain and pre-filter basket.
› Insulation class F;
› Degree of protection: IP55;
› Engine rpm: 2900 rpm;
› Maximum water temperature: 50°C;
› Supplied with ø50 mm unions.

SWIMMING POOL PUMP BLUESPACE LYRA 1.5 INCHES

The packaging for this item is a 'large parcel'. UK delivery is FREE. Di Vapor aims to dispatch all items as soon as possible, with the majority of orders being dispatched on the same day or next working day. Priority next day delivery orders must be received before 3.00pm in order to guarantee delivery by the next working day. We use a variety of different next day couriers including Royal Mail Special Delivery 1.00pm, UPS Next Day and tnt Priority. When entering detailed seller ratings on our feedback page, we would greatly appreciate that delivery time is understood as how quickly we get the item purchased out for delivery. Di Vapor does not have any control over delays caused our carriers (Royal Mail, DPD, UPS, tnt etc) and trust our carriers to deliver the item within the promised it.

PUMP FOR WALL MOUNTED FILTER

QUIET OPERATION AND EASY INSTALLATION Product Features -1.5 inch suction and discharge ports -Asynchronous, two-pole motor -Class insulation: 130(B) IPX5 Waterproof standard -Built-in thermal protection -External heat sink -Transparent lid (SD Series) -Available in 50Hz or 60Hz for 220V/110 -Specially designed unions compatible for both Imperial and Metric standards -316 stainless steel shaft -316 stainless steel mechanical seal -Low noise level, low energy and easy maintenance

PUMP FOR SPA EMAUX ST SERIES

Comet

Volumetric water pumps , qualified in domestic fittings, to increase the system pressure in aqueducts and for automatic water distribution by small autoclave tanks or by hydrosphere units. For the correct functioning of the pump, use clean water, or non-agressive liquidsonly, without sand or other solid im pu rities..

OPERATING CONDITIONS:
– Liquid temperature up to 95°F (for home use according to EN 60335-2-41)
– Temperature max. liquid: 140°F (for other uses)
– Ambient temperature up to 104°F
– Total suction lift up to 23 ft.
MOTOR:
– Single-phase 110/220V – 50Hz
– Two-Pole induction motor (n = 3450 min-1)
– Insulation Class F
– Protection IP 44
MATERIALS:
– Pump body: Cast Iron
– Motor Support: Cast Iron
– Impeller: Brass
– Shaft with rotor:  Stainless Steel AISI 304
– Mechanical seal (50-80): Ceramic/Graphite/NBR

BOOSTER PUMPS CAST IRON

Pump   Body:Stainless Steel
Motor Housing: aluminum
Shaft: 45# steel /stainless steel
Impeller: Brass/Stainless Steel/PPO optional 
Motor: closed, externally ventilated
Insulation Class: B/F
Protection Class: IP44 /IP54
 Max ambient temperature up to 40°C
Mechanical Seal: ceramic steatite/metalized carbon                          
Max fluid temperature up to 40°C 
Max pressure up to 6 bar

BOOSTER PUMP JET STAINLESS STEEL

Pikespool

Wall Mount Pool Filter PK8028 Manufacturer
Pikes PK8028 integrated swimming pool equipment wall-mounted filter is a complete swimming pool filtration system,easy to install and operate,with acid-proof,anti-fading,easy to clean and so on.

WALL MOUNTED FILTER

Made of polyester resin and fibreglass (with plastic base).
Excellent finish.
Plastic lid large diameter.
Fitted with 1” collector arms and diffuser in unalterable plastic.
Fitted with pressure gauge, water drain, and air drainage.
Connections to multiport valve with six positions: filter, backwash, rinse, recirculation, waste and closed.
Maximum working pressure: 2,5 Kg/cm2.

Top Categories

Cooperation